Licensed electricians for new cans, dimmers, and full replacements
Recessed Lighting Installation Findlay OH Done Clean and Code-Correct
Recessed Lighting Installation Findlay OH homeowners can count on starts with a licensed electrician who maps the ceiling before a single hole is cut. We handle new recessed lighting Findlay OH projects, swap out old cans, and wire dimmers so kitchens, basements, and living rooms get even light with no hot spots. Whether you are finishing a basement in Blanchard Valley or replacing flickering cans in a 1960s ranch near South Main, we quote the job, pull the circuit, and test every fixture before we leave.
Live phone supportUpfront optionsBacked workmanship
What's included
What Our Recessed Lighting Installation Includes
Every recessed lighting job we run in Findlay includes the layout, the circuit, the fixtures, and the cleanup. We price the whole scope upfront so there are no surprise line items after the ceiling is open. Add-ons like panel upgrades or extra outlets are quoted before we start, not after.
Ceiling Layout and Marking
We map can positions with a chalk line and painter's tape, confirm joist direction, and get your approval on spacing before any hole saw touches drywall. You see the grid on the ceiling, not just on paper.
Dedicated Circuit Run
A new 15-amp or 20-amp circuit pulled from your panel with Romex cable, stapled every 4 feet, and landed on a correctly sized breaker. We label the breaker at the panel so the next electrician knows what it feeds.
Can Housings and LED Trims
IC-rated housings sized to your ceiling cavity, plus dimmable LED trims in the color temperature you pick. We set each can level with the drywall and confirm the trim ring sits flush with no gaps.
Switch and Dimmer Wiring
A new switch leg from the cans to the wall box, with a Leviton dimmer rated for the LED load. We test the full dimming range and swap the box if it is too shallow for the dimmer body.
Testing and Labeling
Every fixture gets a voltage tester check, the circuit gets a load test, and the panel schedule gets updated. You get a walkthrough of what we installed and how to reset the breaker if you ever need to.
Cleanup and Warranty
Drop cloths, dust-catching hole saws, and a full vacuum pass before we leave. You receive a written labor warranty and our phone number for any follow-up questions about the recessed lighting.
Service overview
What Recessed Lighting Installation Findlay OH Really Involves
Recessed Lighting Installation Findlay OH is the electrical trade of cutting openings in a finished or unfinished ceiling, running a dedicated circuit from the panel, and setting can lights so the trim sits flush with the drywall. We start by checking what the ceiling cavity will allow, then run Romex cable through the joists, secure it with cable staples, and land the conductors in junction boxes. Each fixture gets a wire nut connection, a voltage tester check, and a trim ring that sits level. On a typical 12-light kitchen job we are on site four to six hours.
Most Findlay homes built before 1980 have a single ceiling fixture and no switched neutral, which is why homeowners call us for recessed lighting replacement Findlay projects rather than adding a second light. Older wiring in Hancock County homes often means aluminum branch circuits or cloth-wrapped conductors that will not carry a modern LED load. We test the circuit with a multimeter, confirm the panel has room for a new breaker, and tell you upfront if the cost to install recessed lighting in Findlay OH includes a panel upgrade or just a new run.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How Our Recessed Lighting Installation Process Works
The process flexes to the condition, but these checkpoints keep decisions clear.
Walkthrough and Layout
We walk the room with you, note ceiling joist direction, and mark can positions with painter's tape. You approve the layout before we cut. On a standard kitchen this takes 20 to 30 minutes, and we check the panel for open breaker slots at the same time.
Circuit and Cable Run
We pull a dedicated 15-amp or 20-amp circuit from the panel using Romex cable, drill through joists at the center line, and protect the run with cable staples every 4 feet. A fish tape gets the cable through finished walls without tearing drywall. Most runs take one to two hours.
Cutting and Setting Cans
We cut each opening with a hole saw sized to the housing, then set the can and secure it to the joist or a bar hanger. Junction boxes get wire nut connections, and we verify polarity with a voltage tester before the trim goes on. Twelve cans take about two hours.
Dimmer and Switch Wiring
We install a Leviton dimmer rated for the LED load and wire it to the switch leg. If the wall box is too shallow for the dimmer, we swap it for a deeper box. We test the dimmer through its full range to confirm no flicker and no buzz at low settings.
Testing and Cleanup
We energize the circuit, check every fixture with a multimeter, and confirm the breaker holds under load. Drop cloths come up, drywall dust gets vacuumed, and we walk the room with you. You get a written warranty on labor before we pull out of the driveway.
Tools & methods
Tools and Methods We Use on Every Job
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Klein Tools Voltage Tester
Confirms a circuit is dead before we touch conductors and verifies polarity at every fixture after the wire nuts are made up.
Fluke Multimeter
Measures voltage, continuity, and amperage draw so we can prove a circuit will carry the new LED load before we close up the ceiling.
Fish Tape and Cable Ripper
Pulls Romex through finished walls and joist bays without tearing drywall, and strips cable jacket cleanly for a proper box fill.
Dust-Catching Hole Saw
Cuts clean openings in finished drywall and traps most of the dust in the attached cup, which keeps your kitchen or living room clean.
Circuit Breaker Finder
Maps which breaker feeds a circuit when the panel schedule is wrong or missing, a common issue in older Findlay homes.
GFCI Tester
Tests GFCI protection on nearby outlets while we have walls open, so wet-area receptacles are verified before we finish the job.
Conduit Bender
Forms conduit runs in garages and basements where cable must be physically protected instead of stapled to a joist.
Use cases
When Findlay Homeowners Call Us for Recessed Lighting
These examples show how the service framework adapts rather than forcing every call through one repair.
Basement Rec Room Gains Full Ceiling Height
A Blanchard Valley basement had a dropped ceiling with two fluorescent panels and water stains on the tiles. The homeowner wanted a clean ceiling but did not want to lose more height to a soffit. → We removed the drop ceiling grid, installed eight 4-inch low-profile cans in the soffit areas and open room, and set a small subpanel near the stairs. The room gained 7 inches of headroom and now dims smoothly for movie nights.
1960s Ranch Replaces Flickering Cans
A South Main ranch had four original incandescent cans that flickered and would not accept LED retrofits. The attic wiring was cloth-wrapped, and the breaker tripped whenever the lights ran more than an hour. → We replaced the attic run with Romex, installed four IC-rated LED cans, and swapped the weak breaker for a correctly sized Square D unit. The lights run cool, dim smoothly, and the circuit holds under a full load test.
Problems we solve
Recessed Lighting Problems We Fix in Findlay
Most of our lighting calls start with a symptom, not a plan. Here are the four issues Findlay homeowners call us about most often, and how we handle each one.
Flickering recessed lights on a shared circuit
We test the circuit with a multimeter, tighten or replace the failing connection, and move the lights to a dedicated circuit if the load is the cause. Most flicker calls are resolved the same day.
Old cans that will not accept LED bulbs
We swap the housing for an IC-rated LED can, reuse the existing circuit when it tests clean, and install a dimmer rated for the new load. That is the core of most recessed lighting replacement Findlay jobs.
Tripping breaker when the lights come on
We use a circuit breaker finder and voltage tester to isolate the fault, repair the wiring, and replace the breaker if it will not hold. We never upsize a breaker to stop a trip.
No ceiling light in a room at all
We cut in recessed cans, run a new circuit from the panel, and install a switch at the doorway. A typical four-light bedroom takes about three hours and leaves you with a real ceiling light.
Pricing process
What Recessed Lighting Installation Costs in Findlay
$150 - $350 per fixture installed; most full-room jobs land between $1,100 and $1,900
Number of Fixtures
Price scales per can, but the per-fixture cost drops as the count rises because the circuit run and setup are shared. Six cans cost less per light than two.
Ceiling Access
An open attic or unfinished basement makes the cable run fast. Finished ceilings with no access take longer, and we may need a small drywall patch at the switch wall.
Circuit and Panel Capacity
If your panel has an open slot and the circuit tests clean, the job is straightforward. A full panel or a long home run adds a subpanel or upgrade to the scope.
Customer reviews
What Findlay Customers Say
★★★★★
“We had six old cans in the kitchen that flickered every time the fridge kicked on. The crew traced it to a loose neutral in a junction box and put the lights on their own circuit. No flicker since. They laid drop cloths, vacuumed the drywall dust, and the ceiling looks like the cans were always there.”
★★★★★
“Finished our basement this fall and needed eight recessed lights plus a dimmer. They quoted per fixture, showed up when they said, and had the whole thing done in a day. The inspector passed it without a single correction. I have already recommended them to two neighbors on my street.”
★★★★★
“Our 1950s ranch had one ceiling light in the living room and cloth wiring in the attic. They replaced the old run, added four cans, and installed a dimmer. The price came in right where the quote said. They also flagged a worn breaker and swapped it while they were in the panel.”
How much does recessed lighting installation cost in Findlay OH?
Most Findlay recessed lighting jobs run $150 to $350 per fixture installed, with a typical six-light kitchen landing between $1,100 and $1,900 in 2026. That covers the can, trim, LED module, cable, breaker, and labor. Adding a dimmer runs $85 to $140. If your panel needs a new circuit or a subpanel, expect another $400 to $900 depending on the run length.
How many recessed lights do I need in my Findlay room?
A simple rule is one 6-inch can per 25 to 30 square feet of ceiling, spaced 4 feet apart and 2 feet from the walls. A 12x14 kitchen gets six cans on two rows. A 20x20 basement rec room gets eight to ten. We lay the grid out on your ceiling before cutting so you can see the spacing and adjust it.
Can you install recessed lighting in an existing ceiling in Findlay?
Yes. We cut into finished drywall every week in Findlay homes, using a dust-catching hole saw and a fish tape to run cable through the joist bays. The only ceiling we cannot work in is one with asbestos texture or a concrete slab with no furring space. We check both during the walkthrough and tell you straight away.
What type of recessed lighting is best for Findlay homes?
For most Findlay homes, 4-inch or 6-inch LED cans with a 2700K to 3000K color temperature and an IC-rated housing work best. IC rating matters because it lets the can touch insulation, which most attic ceilings here have. We use dimmable LED trims from Leviton and Hubbell so you get smooth dimming down to 10 percent without flicker.
Related services
Other Electrical Services We Handle in Findlay
New Circuit Installation
Recessed lighting almost always needs its own circuit. We run a dedicated 15-amp or 20-amp line from your panel to the switch box so the lights do not share a load with the microwave or a space heater.
Electrical Rewiring
If your Findlay home still has cloth-wrapped or aluminum branch wiring, we rewire the affected rooms before adding cans. New recessed lighting on old conductors is a code violation and a fire risk we will not leave behind.
Whole Home Rewiring
For a full remodel in Hancock County, whole home rewiring lets us plan recessed lighting, outlets, and switches on one set of drawings. You get a consistent layout instead of patched-in circuits added room by room.Ready when you are
Book Recessed Lighting Installation Findlay OH This Week
Call +14197996088 and we will quote your recessed lighting job, usually the same day. Licensed electricians, code-correct work, and a written labor warranty on every install. If you need recessed lighting replacement in Findlay, we can often get you on the schedule within 48 hours.
Talk with the local team
Request Recessed Lighting Installation
Reach out for a free estimate on New Circuit Installation & Rewiring Findlay OH. We answer calls 24/7 for emergencies and schedule regular work Monday through Friday. Our office is in Findlay, and we serve all of Hancock County. Call, email, or stop by.